Eleaf,

How to Use Eleaf iCare 2 Pod Kit - User Manual

How to Use  iCare 2? 

iCare 2 Pod Assembling: 

1. Pull up the whole tank section, open the bottom cover of the tank with your fingernail in the direction of the arrow (please refer to Picture 2);
2. Drip a few drops of e-liquid into the atomizer head to fully saturate it before first use;
3. Screw the atomizer head into the tank, and put the bottom cover back to its original position;
4. Pull out the mouthpiece, and slowly fill e-liquid into the tank through either of the two holes on the sides; (Note: please do not overfill; please do not fill e-liquid into the center hole.) (Please refer to Picture 3)
5. Put the whole tank section back, let it sit for a few minutes and the iCare 2 is ready for use.

Power on/off:  Press the button 5 times in quick succession within two seconds, and the indicator light will flash 3 times to show the device is powered on. In the same way, it can also be powered off.

Vaping: Keep holding the button to take a puff when the device is powered on. When vaping, the indicator light stays lit. The color of the indicator light changes according to the remaining battery capacity.

Charging: The device can be charged by connecting it with 1A wall adapter or computer via the USB cable. The charging indicator light is red during charging and goes out when fully charged.

Properties and Protections: Atomizer Protection: every time when vaping time exceeds 15 seconds, the indicator light flashes 4 times and the output cuts off automatically.

Short Circuit Protection: if short circuit occurs, the indicator light will flash 5 times and there will be no output.

Low Voltage Protection: when the voltage of the device is lower than 3.3V, the indicator light flashes 40 times and there is no output when vaping. Charge the device to reactivate it.

Resistance Detect: if the output load resistance is higher than 3.0ohm, the indicator light will flash slowly to indicate that no atomizer is detected when vaping; if the output load resistance is lower than 0.6ohm, the indicator light will flash 5 times to indicate a low output load or a short circuit when vaping.

Warranty 

We are not responsible for any damages caused by human error. Legal warranty is applied.

Warnings 

1. Please keep out of reach of children. 2. This product is not recommended for use by young people, non-smokers, pregnant or breast-feeding women, or persons who are allergic/sensitive to nicotine.

Contra-indication 

1. Do not attempt to repair the product by yourself as damage or personal injury may occur. 2. Do not leave the product in high temperature or damp conditions, otherwise it may be damaged. 3. Do not use this product for other purposes except only for vaping and don’t swallow the e-liquid.

Possible Adverse Effects 

1. This product may be hazardous to health and contains nicotine which is addictive. 2. For people with adverse reaction after using this product, it is recommended to use the e-liquid with lower nicotine content or no nicotine

Profile Mesh Style Coil,

The Best Flavor Coil for Wotofo Profile RDA - Vape News

The Best Flavor Coil, Profile Mesh Style Coil

Wotofo is a young e-cigarette brand. You must have heard of its Fotofo Profile RDA, right? This high-performance RDA not only makes the vaping experience richer but also a lot of fun. So what I want to share with you today is the coil from Wotofo, Wotofo Profile Mesh Style Coil.

You will fall in love with Profile Mesh Coil

This is a Mesh coil with a 1.8-ohm resistance. It is made of solid Kanthal A1 material and has a larger heating area. Its recommended power is 40-60 watts. It doesn't require much powerful output to run it, and it's easy to get the good taste you want. It is easy to install and well maintained. I would especially recommend it to fans who like MTL Vaping.

Do you like it? You can go to Sourcemore online shop to buy!

Captain X3 Instructions,

IJOY Captain X3 Kit Settings - Vape Guide

How to set the Captain X3 TCR? 

In the main menu, switch to "TCR" mode indication, press fire button to confirm. Press fire button to choose between TCR M1, TCR M2. Press right/left buttons to select certain parameter. After setup is completed, press fire button to switch to "EXIT". Press right or left button to confirm.

Puff counter

In any mode, the screen shows the number of puffs. If a puff more than 0.8s, it will be recorded as one puff. The device can remember the value even if you remove the battery. The default number is "000". When the number reaches "999”; it will be cleared automatically.

How to clear the puff value manually? 

Press the fire button 3 times in 2s to enter the menu,
Choose  icon to enter the "”setting, press fire button to confirm your choice.

Set the standby mode 

Press the fire button 3 times in 2s to enter the menu,
choose   icon, use+ and - button to choose “Screen Time” area, there are 4 preset choices, press fire button to confirm your choice, the screen will enter standby mode at the selected time.

Upgrade operation

After the computer connected with the device, open the upgrade software on the computer, click the Load File button,
Find the upgrade program on your computer and load it. Upgrade software and firmware are in a same compressed package, every upgrade! program has a unique PID number, enter the corresponding product PID number and then click the Start button to upgrade.

After upgrading, unplug the USB data cable, install the battery and turn on, now you can experience the latest firmware version. (details please check the documentation after download the upgrade package)

How to charge by USB?

When the voltage is lower than 3.3V, the display will show "Low Battery”; then you need to charge the device, please connect the device through the USB cable to the computer or power adapter.
1. in the charging process, the red light is bright, full power will go out
2. in the charging process, the battery voltage is lower than 3.2V, the device is turned off.
3. can not vape during charging
(If the device not be used for a long time, please charge every 30 to 60 days to make sure battery life)

Malfunction

Indication and Protection

PCB temperature overheat protection When the temperature of device is too high, the output will shut off automatically and the screen will display "PCBTOO HOT"

Low power alert: 

When battery voltage is below 3.2V, the device shows" LOW BATTERY"

PCB Atomizer short-circuit protection: 

When atomizer short-circuit occurs, the OLEO screen will display "SHORTED"

No Atomizer: 

when no atomizer connect, the device will display "No atomizer"

Low resistance protection: 

When the resistance is lower than 0.06ohm, the OLED screen will display "OHMS TOO LOW".


When the resistance is higher than 3ohm, the OLED screen will display "OHMS TOO HIGH".

Warnings

1. Please read the manual carefully before use
2. Please do not keep the e-juice inside the atomizer if the device is not going to be used for a long period
3. Please take out of the battery from device when it's not used for a long time
4. Please keep the device away from children, pregnant women, and minors (under 18 years of age)

E-cig,

IJOY ELITE PS2170 Kit Instruction - Vape Manual

ELITE PS2170 Operation Instruction: 

Power On/off

Press the fire button 5 times m quick succession to turn the d, on and off. After switch on, OLED display PS 2170 logo and software version number at stand by mode.

(Note:
Please adjust the wattage to a proper range to match the atomizer you used before using.

Vaping 

While the device is power on, just keep pressing the fire button to vape
(Firing timeout: 10 Seconds)
While the device is power on, the OLED screen default display VW Mode.

General Functions 

Enter Into The Main Menu
Press the fire button 3 times to enter into the main menu. Press the right and left regulatory buttons to switch among different functions. Press the fire button to confirm.

Power Mode 

In the main menu, switch to"  "setting, press f ire button to confirm Press right and left buttons to adjust the wattage.

Intensity Setting In Power Mode
In the main menu, switch to intensity setting, press fire button to confirm Press right and left buttons to switch among below4 modes. In user mode, press fire button to switch among each setting columns. Press right and left buttons to adjust the wattage After setup is completed, press fire button to switch to "EXIT". Press right or left button to confirm.

Norm Mode: Maintains the currently set power.
Hard Mode: 30% higher than the currently set power.
Soft Mode: 20% lower than the currently set power.
User Mode: Customize the power output for the first three seconds of each puff, with each setting column representing half a second.

Temp Mode 

Ni/Ti /SS/TCRM1/TCRM2
In the main menu, switch to ”T" setting, press fire button to confirm. Press right and left buttons to switch among Ni/Ti/SS/Ml/M2 modes. Press fire button to confirm. Press right button, when "W" flashing, press right and left buttons to adjust wattage. Press left button, when"°F" or"℃"flashing, press right and left buttons to adjust temperature value.
The temperature unit will cycle between ° F and °C when the minimum or maximum temperature is reached.


In the temperature control mode to replace the heating wire, the first let Heating wire in the indoor temperature, after installed the heating wire. The screen will appear the heating wire resistance, Figure 1 is the heating wire Of the initial value, if the "resistance" is very accurate directly Use, if not very accurate then need to correct the heating wire Of the resistance.

TCR Mode (M1, M2) 

With the TCR (Temperature Coefficient of Resistance) function available now, you can customize your temperature control coils (Ni, Ti, SS) on your own In the main menu, switch to "T” setting, press fire button to confirm. Switch to Ml /M2 modes. Press fire button to confirm.

E-cig,

Geekvape Tsunami24plus Instruction - User Manual

Thank you for choosing GEEKVAPE

Please read the user manual before using this product for better user experience.
Keep the user manual for future reference

Exploded View 

Tsunami24plus Overview

Installation Steps

1. Get the product
2. Screw off the top cap as shown in picture
3. Build Coil
4. Fill your juice
5. Rotate the top cap as shown in picture.

Warning

Product not for use for Pregnant or Children under the age of 18
Do not use or keep near a fire or strong heat source

Ammit 25 Problems,

Geekvape Ammit 25 RTA Instruction - User Manual

Thank you for choosing GEEKVAPE

Please read the user manual for better user experience
Keep the user manual for future reference.

Exploded View

Highlight

Improved vapor production
Enhanced 3D airflow system’
Simplified deck makes building even easier

Setup guide

Drip tip height: 10mm
Drip tip diameter: 15mm
Height: 48mm
Base diameter: 25mm
Capacity: 2ml/5ml

Contents

1* Ammit 25 RTA    1* Spare parts polybag
1* Spare Glass Tube   1* User Manual
1* Allen Key    1* Extra 810 Top cap
1* 810 Drip tip

How to use Ammit 25 RTA

1. Get the product
2. Screw off the top cap as shown in picture
3. Build Coil
4. Fill with e-liquid
5. Screw on the cap as shown in picture

BF RDA,

Damn Vape Dread BF RDA - The Details You Should Know

Damn Vape is a young e-cigarette brand. However, I think you must be deeply attracted to it. Recently, Damn Vape introduced an RDA, Dread BF RDA. This RDA is somewhat different from our usual RDA. Brought a Lolly Tool in its packaging. With it, we can rebuild a "circling" coil.


The spiraling coil gives us a different feeling. It supports us to install more cotton because of the larger contact area. Through the side of the cellular airflow control system, the air can be better contacted with the coil. It has a honeycomb airflow ring on the side that offers a variety of air intakes. Do you like it? Let's take a look at more Damn Vape Dread BF RDA details:

Parameter

Height: 24mm
Diameter: 24mm
Thread: 510 thread
Material: stainless steel
Drip tip type: 810 resin
Juice well depth: 8mm

Aspire,

How to Use Aspire Feedlink Revvo Kit - User Manual

Read this information leaflet fully before you start using this product as it contains important information. The notes below relate to when the device is filled with liquid that contains nicotine.

This product is intended for adult smokers. This product is not recommended for non-smokers, young people under the age of 18 years, pregnant or breast feeding women and those experiencing general ill health.

Contents:

1* Feedlink mod
1* 2ml Revvo Boost tank 2* Coils (0.10-0.14Ω) 1* Glass tube
11* O-rings
2* Warning card
1* User manual
1* Warranty card

Tank Features

• Bottom fill (fill through the Squonk pin)
• Adjustable airflow
• 2ml capacity
• Innovative ARC(Aspire Radial Coil) technology
• Coil resistance 0.1-0.14Ω
• Wattage range: 70-80W
• Diameter: 24mm
• Length: 41mm

Filling

Squeeze the ejuice bottle inside of the mod to fill the tank.

Coil installation

1. Unscrew and remove the top chamber.
2. Unscrew and remove the mounting screw.
3. Remove the used ARC coil by lifting over the metal pin.
4. Place a new coil over the metal pin, make sure the coil edge is lined up with the tank.

5. Screw the mounting screw back onto the base hardware.
6. Replace the top chamber.
NB: the mounting screw also acts as a ‘spit-back’ guard.

Replacing glass

1. Unscrew and remove the glass securing ring from the base hardware.
2. Pull and remove the used glass tube.
3. Insert a new glass tube.
4. Screw the glass securing ring back onto the base hardware.

Feedlink mod specifications

Output voltage: 3.0-4.2V
Resistance parameter: 0.1-3.5ohm
Modes: Bypass output
Non-adjustable Wattage/ Voltage
Battery type: Single 18650 high rate discharge battery
(discharge rate ≥35A)
Continuous firing time: 10 seconds
Silicone bottle capacity: 7ml

Safety features

• Automatic cutoff: The continuous fire time is 10 seconds, after 10 seconds of continuous firing the mod will stop firing and the LED light under the fire button will flash 10 times.
• Battery reverse protection

Short circuit protection: When the mod detects a short, the LED light will flash 2 or 3 times.

Over discharge protection: When the battery level is below 3.2V, pressing the fire button the orange light will flash 15 times.
Over heat protection: When the temperature of the control board is above 75 degree Celsius, the mod will shut off and the LED light will light up blue and orange for 3 seconds.

Operating instructions

Installing an 18650 battery into the mod, the LED light will flash blue and orange 2 times.

When the battery level is above 3.8V, the LED light will be blue only, when the battery level is between 3.5V and 3.8V, the light will be a mixed color of blue and orange; the orange light means the battery level is below 3.5V


Click the fire button 5 times rapidly to lock or unlock the device the LED light will flash blue and orange 3 times to indicate lock or unlock. When the mod is unlocked, pressing the fire button the blue or orange LED light will light up according to the battery level.

Silicone e-juice bottle installation

Lightly push in the bottle securing cap at the bottom of the mod.

Then twist counter-clockwise direction to remove the securing cap.

Insert a new silicone e-juice bottle into the plastic carrier frame, reinsert the frame into the mod then push the knob and twist clockwise direction to secure.

How to fill the Silicone e-juice bottle?

1. Unscrew and remove the metal cap at the top of the bottle.
2. Add your preferred e-juice into the bottle.
3. Replace metal cap.

Battery installation

1. Invert the Feedlink mod and unscrew the battery cap.
2. Insert an 18650 battery into the battery compartment with positive end pointing down and negative end pointing up.
3. Screw the battery cap back onto the mod.

e-cigarettes,

What Will You Get from IJOY IVPC Vape 450mAh Pod

IJOY brought us its new Pod Kit, IVPC. This is a device with a 450mAh built-in battery. It not only has a refined look but also has a great vaping experience. Here we will get an IVPC coil with better atomization and vaping performance.



As a Pod Kit, IJOY IVPC allows us to carry it with ease. I will strongly recommend it to vapers who want to find portable vape or tobacco substitutes. This device has a 9W output and comes with a 1.6ohm coil. This shows that it can be used very well with high-nicotine e-juice or salt-nic. With the combination of low output and high resistance coil, e-juice can achieve better atomization and make high-nicotine vaping more comfortable. If you like this product too, let's take a look at what’s in the IJOY IVPC package:

An IJOY Rechargeable IVPC Device 450mAh
An IJOY IVPC Cartridge 2.0ml
a USB cable
A Manual (please read the instructions carefully before use to ensure a better vaping effect)
a Warranty card
a Warning card

E-cig,

Sigelei Vcigo Moon Box Kit Reviews

Sigelei is an e-cigarette brand from China. The brand has always given me the impression of innovation and fashion, this time Sigelei did not let me down. Today I want to share with you a new product from Sigelei, Vcigo Moon Box Kit.



This product consists of two parts, the Vcigo Moon Box mod and Moonshot RDTA Atomizer. If the Vcigo Moon Box mod is the best element to attract you, then I am also shocked by the Moonshot RDTA Atomizer. Moonshot is an RDTA Atomizer, which means we will be able to build the coil we want.



The Vcigo Moon Box supports a coil with a resistance range of 0.1 ohm-2.5 ohm. Now whether you are a vapor chaser or a taste chaser, this product will give you an unparalleled experience. Where can I buy Vcigo Moon Box? If you want to buy a free Vcigo Moon Box kit, then I would recommend you to buy it at Cloumix. Buy now and you will not only enjoy free shipping, but also a 6 month warranty. what are you waiting for?

E-cig,

The Right Way to buy VOOPOO Panda AIO Starter Kit

VOOPOO is an e-cigarette brand that is different from other e-cigarette brands. I have never seen LED lighting design on this brand, but its products make me feel very individual. You think so, right? The Panda Kit is a very cute e-cigarette. This product has a panda shape and is very popular among everyone.



Hide a huge secret under its cute appearance. This product has a 1100mAh battery capacity and can store 5ml e-juice. Here we are free to switch between salt-nicotine vaping and common vaping by replacing the pod tank. It is an ergonomic design product, so we can control it very well with one hand. Panda uses a vertical airflow structure to give us a better taste and a larger amount of vapor. Where can I buy the VOOPOO Panda AIO Starter Kit? Now you can go to VOOPOO's official partner Cloumix to make a purchase. This is an e-cigarette seller from China and it can offer a Panda Kit 6 month warranty. what are you waiting for?

e-cigarettes,

Are You Looking for VOOPOO Panda AIO Pod Kit?

E-cigarettes are no longer the kind of pen style Kit we first knew. Now the emergence of Pod Kit has made e-cigarettes more and more abundant. There are a lot of e-cigarettes in various shapes that give us more choices. We already have a dolphin-shaped e-cigarette and a penguin-shaped e-cigarette. So, today brings you the most cute panda-shaped e-cigarette, VOOPOO Panda AIO Pod Kit.



What is VOOPOO Panda AIO Pod Kit? This should be the cutest e-cigarette I have ever seen! Panda is known as the national treasure of China. Yes, you must see Kung Fu Panda! The panda is really cute. Today's product not only has a cute appearance, but also has a strong vaping performance. A 1100mAh internal battery is hidden in this ergonomic design and panda kit can store 5ml e-juice. There are two pod tanks of different effects, one of which is specially designed for salt-nicotine, it has a 1.2 ohm coil, and the recommended power is 8W. If you are a friend who likes high-nicotine e-juice or salt-nicotine , then Panda Kit is your best partner. I think there are many products of the same ability on the market, but no one product can be as cute and high-performance as VOOPOO Panda! What do you think?

AIO Starter Kit,

Vaporesso Orca Solo AIO Starter Kit Reviews | The Right Choice

Hi, everyone. It's great to meet you all. Today I will share with you the experience of Vaporesso Orca Solo AIO Starter Kit. This is a product that I am still very satisfied with. Before buying this product I was worried that I could not adapt to the electronic cigarette, but I fell in love with vaping.


This is a product that does not require me to worry about the power problem. It satisfies my one-day vaping needs. Of course, I only need 45 minutes of charging time and it will be revived. This product does not have the display as other e-cigarettes, but it brings a longer lasting vaping time. And for those of me who want to try vaping, Orca Solo has satisfied my vaping needs. I particularly like the taste of this product, especially when I completely open the airflow, I feel the world is mine. The whole process is smooth and the taste is well preserved. It really is worth trying. Where can I buy Vaporesso Orca Solo AIO Kit? I bought this product at Cloumix and I think you can also. Not only because it offers a discount I am satisfied with, but also its six-month warranty. It is really sincere and I think I would recommend it to more people.

E-cig,

What Will You Get from Orca Solo Kit? | 2018 New Starter Kit

Orca Solo is a Starter Kit from Vaporesso. Then this product has an 800mAh battery, and 1.5ml capacity. This is a classic electronic cigarette shape. A fire button can do all the manipulations. For beginner, this will be the best transitional product. Not only is it economical, but also the vaping experience is extraordinary.

What will you get from it?

So before you buy, let’s take a look at what’s in the Orca Solo Kit package:


1 . Vaporesso ORCA Solo Kit 800mAh battery with 1.5ml Tank (this is an AIO device, all brings a simpler use. Just remove the metal sleeve, we can add e-juice)

2. A User Manual (Please read the user manual carefully before use. If you are using electronic cigarette for the first time, please drip a small amount of e-juice directly on the coil to prevent the cotton from burning)

3. Two Orca Solo Coil (The two coils have a resistance of 1.3 ohms. They are also the key accessories for this product to bring excellent taste)

4.USB Cable (Using the charging cable, we can directly connect the computer or other charger to charge)

E-cigarette Mod,

2018 Worth Buying E-cigarette Mod | Wismex LUXOTIC NC Mod

The types of e-cigarettes are getting richer and we get a lot of pleasure from electronic cigarettes. Of course, electronic cigarettes have also succeeded in helping many people get rid of cigarettes. What we share with you today is a product from Wismec, Wismex LUXOTIC NC Mod. So what surprise would it bring?


What is the Wismex LUXOTIC NC E-cigarette Mod? This is a device powered by two 20700 batteries, its maximum output can reach 250W. Of course, we can continue to use 18650 batteries, but we need to use Battery Sleeve. This is a product that reflects your personal charisma. Its unique design allows you to stand out from the stereotyped product quickly. Its uniqueness is for people who understand it. Will it be you? The 250W output requires that you use a voltage adjustment knob, which will give you more fun. Trust me. 510thread can support you to use many Atomizers on the market. If you like RDA Vaping, Wismex LUXOTIC NC Mod will not disappoint you. Perhaps you will be disappointed that it has no display, but in the end you will know that this is the best design. Everything it takes depends on your judgment. This is a device that is completely controlled by you. It belongs to you. what do you think?

deals,

Here Are the Special E-cigarettes You Want

E-cigarettes are already a new partner in our lives. Many friends have also begun to change from smoking to Vaping. Vaping not only allows us to lead a healthier life, but also adds a lot of fun to our lives. If you want to try e-cigarettes, this site allows you to buy special e-cigarettes. This is my favorite e-cigarette online store, Cloumix. This site often carries out e-cigarette special events, and it sells vape Kit can get a six-month warranty. This is really much better than other online malls. Whether it is the Starter Kit, or advanced vape Kit, or RDA Kit, here you can buy. what are you waiting for?

2018 World Cup,

2018 World Cup Souvenir E-cigarette | iJust 3 with ELLO Duro Kit

Yes, if you are a vaper like the World Cup, there will be an electronic cigarette that you can't refuse, iJust 3 with ELLO Duro Kit. iJust 3 with ELLO Duro Kit comes with a cute football shape glass tube, and a torch Style vape battery. This is an electronic cigarette born for the 2018 World Cup. When you hold this product, you can imagine how much attention it will attract for you. This is a unique World Cup theme electronic cigarette. Do you really like football? Do you really like the 2018 World Cup? Left the best souvenir for the 2018 World Cup. There are now two colors to choose from: Red god and black sivle. Do you like it? Where can I buy the World Cup version of Eleaf iJust 3 Kit? Now you can buy it at Cloumix Vape Online Store. 24 hours fast shipping speed, official certification shop, let you get ijust3 at the best price. Do not hesitate.

e-cigarettes,

2018 Best Pod KIT | IJOY Pole Pod Starter Kit

Pole Pod Kit is IJOY's latest AIO Starter Kit. This is also a new choice for friends who like Pen Style Kit. What is the IJOY Pole Pod AIO Starter vape Kit?  It has a 600mAh battery and comes with a fire button. If you are a vaper like MTL Vaping, then IJOY Pole Pod Starter Kit won't disappoint you. It is accompanied by a top airflow MTL Atomizer that satisfies our quest for MTL Vaping. what do you think?

Chinese Valentine's Day,

Chinese Valentine's Day Shopping at Wotofo Authorized Online Store

Good #news, huge #sales from cloumix.com for Chinese Valentine Day from 20th, May to 31st, May.

You Can Get:

1.$5 off over $30 with code: CM5LOVE

2. 20$ off over $100 with code: CM20LOVE

3.15% off on your first purchase for new members

4. Freeshipping for purchase over $52.

Click here https://www.cloumix.com/ and add your cart!!

e-cigarettes,

Chinese Valentine's Day Shopping at Freemax Authorized Online Store

Good #news, huge #sales from cloumix.com for Chinese Valentine Day from 20th, May to 31st, May.

You Can Get:

1.$5 off over $30 with code: CM5LOVE

2. 20$ off over $100 with code: CM20LOVE

3.15% off on your first purchase for new members

4. Freeshipping for purchase over $52.

Click here https://www.cloumix.com/ and add your cart!!

e-cigarettes,

Why Is the Stick V8 Kit An Unmissable Starter Kit?

Hi, guys! In the last two weeks, I bought a Stick V8 Kit. Now that I have been using it for a while, I would like to share with you today my experience with the Stick V8 Kit. I hope my article will help you.


Well, when we first got this device, I felt it was still a bit heavy. It's a black carton pack, with a large "SMOK" logo on the front of the box. After opening, you will see a stick v8 battery, a TFV8 Big Baby Tank, and a 0.25 ohm replacement coil. After you remove these items, at the bottom of the box is a charging cable, a user manual, a vape band and some accessories, then this is all the packaging. The Stick V8 Battery is made up of a 3000mAh battery, so it's slightly wider in diameter than the Aspire vape pen, but it doesn't affect the use at all.

 This device has only one fire button, so you only need to press the button to use it. Surrounding the fire button is a battery indicator that lights up when you turn on/turn off/using/low power, but only the frequency of the flash is different.


 What I have to praise is that the use of this indicator during the day time can still be clearly seen. I like it very much. Of course, TFV8 Big Baby Tank did bring me a good experience, especially in vapor production. It also allows us to replace different atomizer coils, so the experience will be more comprehensive. I really like it.

Cloumix,

FreeMax New Partner In China, One Of The Three Major E-cig Companies

FreeMax is a professional manufacturer and exporter of electronic cigarettes/Vapor hardware to all around the world. Now that Cloumix has been officially authorized by FreeMax, you can purchase authentic electronic cigarettes from FreeMax on Cloumix Vape Online Store. Cloumix guarantee that the products we sell are all from FreeMax products, and there is no falsehood. You can also verify the authorization information through the link below the article.

Cloumix vape online store: https://www.cloumix.com/


Check the authenticity of the Cloumix here:
http://www.aspirecig.com/business-partners/china/
https://www.smoktech.com/global-partner

Cloumix,

Joyetech New Partner In China - Cloumix Technology Co., Ltd

Now, Cloumix has been officially authorized by Joyetech, so you can buy genuine products from Joyetech on Cloumix Vape Online Store. You can also verify the authorization information through the link below the article.

Being the best e-cigarette manufacturer, Joyetech enjoys great reputation and popularity with our reliable e-cigarettes, vaporizers, vape pens, e-cig box mods and varies tanks and e-liquids with different flavors. Joyetech will continue to bring us a better vaping experience.

Cloumix vape online store: https://www.cloumix.com/


Check the authenticity of the Cloumix here:
http://www.aspirecig.com/business-partners/china/
https://www.smoktech.com/global-partner