E-cig,
Press the fire button 5 times m quick succession to turn the d, on and off. After switch on, OLED display PS 2170 logo and software version number at stand by mode.
(Note:
Please adjust the wattage to a proper range to match the atomizer you used before using.
While the device is power on, just keep pressing the fire button to vape
(Firing timeout: 10 Seconds)
While the device is power on, the OLED screen default display VW Mode.
Press the fire button 3 times to enter into the main menu. Press the right and left regulatory buttons to switch among different functions. Press the fire button to confirm.
Intensity Setting In Power Mode
In the main menu, switch to intensity setting, press fire button to confirm Press right and left buttons to switch among below4 modes. In user mode, press fire button to switch among each setting columns. Press right and left buttons to adjust the wattage After setup is completed, press fire button to switch to "EXIT". Press right or left button to confirm.
Norm Mode: Maintains the currently set power.
Hard Mode: 30% higher than the currently set power.
Soft Mode: 20% lower than the currently set power.
User Mode: Customize the power output for the first three seconds of each puff, with each setting column representing half a second.
In the main menu, switch to ”T" setting, press fire button to confirm. Press right and left buttons to switch among Ni/Ti/SS/Ml/M2 modes. Press fire button to confirm. Press right button, when "W" flashing, press right and left buttons to adjust wattage. Press left button, when"°F" or"℃"flashing, press right and left buttons to adjust temperature value.
The temperature unit will cycle between ° F and °C when the minimum or maximum temperature is reached.
In the temperature control mode to replace the heating wire, the first let Heating wire in the indoor temperature, after installed the heating wire. The screen will appear the heating wire resistance, Figure 1 is the heating wire Of the initial value, if the "resistance" is very accurate directly Use, if not very accurate then need to correct the heating wire Of the resistance.
IJOY ELITE PS2170 Kit Instruction - Vape Manual
ELITE PS2170 Operation Instruction:
Power On/off
Press the fire button 5 times m quick succession to turn the d, on and off. After switch on, OLED display PS 2170 logo and software version number at stand by mode.
(Note:
Please adjust the wattage to a proper range to match the atomizer you used before using.
Vaping
While the device is power on, just keep pressing the fire button to vape
(Firing timeout: 10 Seconds)
While the device is power on, the OLED screen default display VW Mode.
General Functions
Enter Into The Main MenuPress the fire button 3 times to enter into the main menu. Press the right and left regulatory buttons to switch among different functions. Press the fire button to confirm.
Power Mode
In the main menu, switch to" "setting, press f ire button to confirm Press right and left buttons to adjust the wattage.Intensity Setting In Power Mode
In the main menu, switch to intensity setting, press fire button to confirm Press right and left buttons to switch among below4 modes. In user mode, press fire button to switch among each setting columns. Press right and left buttons to adjust the wattage After setup is completed, press fire button to switch to "EXIT". Press right or left button to confirm.
Norm Mode: Maintains the currently set power.
Hard Mode: 30% higher than the currently set power.
Soft Mode: 20% lower than the currently set power.
User Mode: Customize the power output for the first three seconds of each puff, with each setting column representing half a second.
Temp Mode
Ni/Ti /SS/TCRM1/TCRM2In the main menu, switch to ”T" setting, press fire button to confirm. Press right and left buttons to switch among Ni/Ti/SS/Ml/M2 modes. Press fire button to confirm. Press right button, when "W" flashing, press right and left buttons to adjust wattage. Press left button, when"°F" or"℃"flashing, press right and left buttons to adjust temperature value.
The temperature unit will cycle between ° F and °C when the minimum or maximum temperature is reached.
In the temperature control mode to replace the heating wire, the first let Heating wire in the indoor temperature, after installed the heating wire. The screen will appear the heating wire resistance, Figure 1 is the heating wire Of the initial value, if the "resistance" is very accurate directly Use, if not very accurate then need to correct the heating wire Of the resistance.
